If you specify motion control for a living, you know the names. Siemens, Rockwell, Mitsubishi and their peers are the safe shortlist. They earned that place. A newer platform has to give you a reason to look twice, and a good one has nothing to do with a flag on a brochure.

Here is how we compare a platform from ICON when a customer asks. Eight questions. Six are on most spec sheets. The last two usually are not, and they end up deciding more projects than the numbers do.

TL;DR

  • Compare axes and refresh rate together, never one without the other.
  • Ask how a sync number was measured, not just what it says.
  • A protocol's lock-in risk outlives the machine it is specified into.
  • Newer platforms have honest gaps: history, service footprint, third-party ecosystem. Ask about them.
  • Sureton's job is the sizing, the English documentation and the local support around the product, not the technology claim.

1. Axis count is two numbers, not one

"Up to 256 axes" sounds decisive until you ask over what period. ICON's ICC-E large modular PLC is rated for up to 256 axes, with 64 axes refreshed per millisecond and a 1 ms control cycle. Those three numbers travel together. Drop one and the claim means something else. Put the axis ceiling and the refresh rate side by side when you compare. A bigger headline figure with a slower refresh can move fewer axes where it counts.

2. Ask how the sync figure was measured

IEEE 1588 PTP V2 at ±100 ns is a real, checkable number on ICON's industrial Ethernet switches. In a fly-capture or registration application, the question is whether it holds under load across the whole axis group, not in an idle lab test. Ask any vendor, established or new, for the conditions. A supplier who answers with conditions is telling you something useful.

3. The network choice outlives the machine

Protocols are where lock-in quietly happens. ICON builds on standard industrial Ethernet and EtherNet/IP. CIP's media-independent design means the architecture can move to a new physical network without being rewritten. Ask every bidder the same question: if the plant changes its network in ten years, what has to be replaced? We won't claim ICON supports every fieldbus on the market. It doesn't. We'll tell you exactly which ones it does support, so you can judge the fit before you commit.

4. Power and the bus, not just the motor

The servo range runs 0.4–132 kW per axis, continuous, with ICM-I motors up to 57.5 kW. On a multi-axis machine the more interesting question is what happens to braking energy. ICON's common DC bus with active front end shares regenerated energy across axes instead of burning it in resistors. The established brands offer this too. The point is to compare how it is wired, how much cabinet space it takes, and whether the whole drive family supports it or only the top model.

5. Engineering software is part of the platform

ICS Studio is ICON's own IEC 61131-3 environment. It covers LD, ST and SFC, with online simulation, and it runs across the full ICC controller family. Judge it the way you'd judge any engineering tool. How steep is the learning curve? Does simulation work before the hardware arrives? Does a program move cleanly between controller sizes? ICON has an honest advantage here and an honest limit. One tightly integrated toolchain. A smaller third-party ecosystem than the platforms that have been around for decades.

6. Maintenance you can schedule around

The ICC-E and ICC-P controllers use an embedded energy-storage module instead of a backup battery, and ICC-E rides through a brief supply dip without an external UPS. On the I/O side, ICD-B modules are 12 mm wide and hot-swappable. Small line items on a quote. Large items in a downtime review.

7. Where a newer platform still has to earn its place

This is the part a sales deck leaves out, so we'll say it plainly. ICON was founded in 2016. It has no decades of field hours and no dense global service network. Third-party integration breadth is still growing. If your programme depends on a particular software module, check compatibility before you assume it. If your site is far from a supported region, ask how spares and engineering support actually reach you. Real trade-offs, not footnotes.

What ICON does have is traceable: a full control stack developed in-house since 2016, selection into the MIIT advanced-applicable-technology list in 2025, and investor backing disclosed publicly. That's a decade of evidence, still growing. It is not thirty years of installed base, and we won't pretend otherwise.

8. What Sureton actually adds

ICON develops and manufactures the product. Sureton is the component supplier and export channel for it. Our part is the work around the specification. We size each axis against your real cycle rather than the nameplate, send English documentation and parameter sheets, coordinate spares, and answer when something needs checking. We're not going to tell you a newer platform is identical to an established one. We'll tell you where it fits and where it doesn't, then let you decide.

A checklist you can take to any vendor

  • Axis ceiling and refresh rate, stated together.
  • Sync figure with its measurement conditions.
  • Protocols supported, and an explicit list of those not supported.
  • Power range per axis, continuous, and how regeneration is handled.
  • Engineering tool: languages, simulation, portability between controllers.
  • Maintenance items: batteries, fans, replaceable parts.
  • Field history, service coverage, third-party integrations.
  • Who provides local sizing, documentation and support, in writing.

If you are weighing a platform change, send us your axis list and cycle times. We'll run the sizing against your real motion profile and tell you, in plain terms, whether this platform fits. Including when it doesn't.